In Excel: select the cells, then grab the small green square at the bottom-right corner — the fill handle — and drag it down or across to copy values or extend a series; double-click it to fill down to the end of the adjacent data.
On this page7
Enter enough values to define the pattern (one cell to copy, two cells for a series).
Select those cells so the fill handle appears at the bottom-right.
Drag the handle down or across, or double-click it to fill down to the end of the adjacent data.
Click the AutoFill Options button to pick Copy Cells, Fill Series, or Fill Formatting Only.
Use Ctrl+D to fill down or Ctrl+R to fill right without dragging.
What this does
The fill handle is the small green square at the bottom-right corner of a selection. Dragging it copies the selected cells or extends a detected series, and double-clicking it fills down to the bottom of the data in the neighboring column. AutoFill reads the pattern in what you selected — 1, 2, 3… or Jan, Feb… — and continues it. Ctrl+D fills the selection down from the cell above; Ctrl+R fills right. After a drag, the AutoFill Options button appears so you can switch between Copy Cells, Fill Series, and Fill Formatting Only. Before you run it on a workbook other people depend on, try it on a copy or a few rows first. Undo only reaches back through the current session, so a quick trial run is the cheapest way to see exactly what will change before the file is saved and shared. For “use autofill in excel”, the reliable version is a short checking loop, not just the first command that appears to work. Run it on a deliberately small range first, watch how the affected cells change, and only then apply the same setup to the full sheet. When this is a ribbon command, the selection matters more than the button: confirm the range, apply the command, then spot-check the output before saving. That is what makes a workflow that saves repeating the same clicks every week useful in real work: repeatable, auditable, and not dependent on memory or luck.
A worked example
Type 1 in A1 and 2 in A2, select both cells, then drag the fill handle down — Excel reads the step of 1 and continues 3, 4, 5… If you instead dragged a single cell containing 1, it would copy 1, 1, 1 until you switch to Fill Series. Dragging the fill handle is the fastest way to repeat a value or build a numbered or dated series down a column without typing each cell. When the result is not what you expected, undo straight away rather than repairing it by hand — undo restores the sheet exactly, while manual fixes tend to leave small inconsistencies behind that surface later.
In Google Sheets
This is a command rather than a formula, so there is no syntax to carry over. Google Sheets arranges its commands in menus across the top instead of a ribbon, names some of them differently and does not have every Excel command — look for the equivalent in the Sheets menus or its help before assuming the steps match. Keep this page bookmarked for the next time the same question comes up. Better still, repeat the steps once in your own workbook — doing it yourself is what turns a copied answer into something you remember. Treat “use autofill in excel” as a routine rather than a one-off. Once you know which setting or command controls it, the same few steps handle every workbook where it comes up in Excel, and you can explain them to a colleague in a sentence.
Common mistakes
- Dragging one cell and expecting a series — a single cell copies; give it two cells to set the step.
- Double-clicking the handle when the adjacent column has gaps, so the fill stops early.
- Ignoring the AutoFill Options button when Excel guessed copy instead of series.
- Holding the wrong corner — the move pointer (four arrows) drags the cell, not the fill handle.
Frequently asked questions
Where is the fill handle?
It is the small green square at the bottom-right corner of the selected cell or range.
How do I fill down without dragging?
Select the range and press Ctrl+D to fill down, or Ctrl+R to fill right.
Why does my drag copy instead of counting up?
A single starting cell copies. Enter two values first, or open AutoFill Options and choose Fill Series.
Other ways people ask this
People reach this page typing “how do i use autofill in excel”, “how do you use autofill in excel”, “autofill a formula in excel” and “excel autofill formula”, among other phrasings; whichever wording you used, the fix above is the one you want.
Why do people search for this in so many different ways?
Because the same task has many names. “how do i use autofill in excel”, “how do you use autofill in excel”, “autofill a formula in excel” all point at the one operation explained on this page, which is why they all lead here.